OEM/ODM Series 30200-Single Row Tapered Roller Bearings Company, Factory

Categories

Series 30200-Single Row Tapered Roller Bearings

Metric Series
Inch series

Design Variants
Cage
Tolerance
Internal clearance

Additional the standard metric single row taper roller bearings listed in the bearing table, DHK also produced single row taper roller bearings with flanges on outer rings (suffix R), only outer rings of taper roller bearing (prefix L), inner rings with the cage and rollers (prefix R) and other special taper roller bearings according to customer

Due to the single row taper roller bearings only can accommodate one direction axial force, these bearings are frequently used as pairs. Upon request, DHK can provide these bearings at Face- to-Face arrangement (suffix DF), Back-to-Back arrangement (suffix DB) or in tandem arrangement (suffix DT), as shown in the below sketch.
DHK taper roller bearings are fitted with pressed steel cages as standard. Because the cages of taper roller bearings usually protrude beyond the bearing faces, special care must be taken to follow the recommended abutment dimensions.

DHK single row taper roller bearings are produced to normal tolerance class (PN) as standard.

These bearings also may be produced with closer tolerance such as P6X on request.

Detail tolerance values are listed in the chapter of tolerance of metric taper roller bearings, page 14. The width tolerance of paired bearings is decided by the clearance and Ts.

Tolerances for DHK metric taper roller bearings (excluding tapered roller bearings)

All dimensions shown in (mm):

Tolerances in (um):

Inner Ring

Tolerance class PN/(Normal)


Nominal bore diameter		Deviation	Variation	Variation	Ring width deviation	Radial runout	Ring width deviation
<=	<=	△dmp	Vdp	Vdmp	△Bs	Kia	△Ts	△T1s	△T2s
10 18		0 -12	12	9	0 -120	15	+2000	+1000	+1000
18 30		0 -12	12	9	0 -120	18	+2000	+1000	+1000
30 50		0 -12	12	9	0 -120	20	+2000	+1000	+1000
50 80		0 -15	15	11	0 -150	25	+2000	+1000	+1000
80 120		0 -20	20	15	0 -200	30	+200 -200	+100 -100	+100 -100
120 180		0 -25	25	19	0 -250	35	+350 -250	+150 -150	+200 -100
180 250		0 -30	30	23	0 -300	50	+350 -250	+150 -150	+200 -100
250 315		0 -35	35	26	0 -350	60	+350 -250	+150 -150	+200 -100
315 400		0 -40	40	30	0 -400	70	+400 -400	+200 -200	+200 -200
400 500		0 -45	45	34	0 -450	85	+400 -400
500 630		0 -50	50	38	0 -500	100	+500 -500
630 800		0 -75	75	56	0 -750	120	+600 -600
800 1000		0 -100	100	75	0 -1000	120	+750 -750
1000 1250		0 -1250			0 -1250	120	+1000 -1000
1250 1600		0 -160			0 -1600	120	+1500 -1500
1600 2000		0 -200			0 -2000	120	+1500 -1500

Outer Ring

Tolerance class PN/(Normal)

Nominal outer diameter		Deviation	Variation	Variation	Radial runout
<=	<=	△Dmp	VDp	VDmp	Kia
18 30		0 -12	12	9	18
30 50		0 -14	14	11	20
50 80		0 -16	16	12	25
80 120		0 -18	18	14	35
120 150		0 -20	20	15	40
150 180		0 -25	25	19	45
180 250		0 -30	30	23	50
250 315		0 -35	35	26	60
315 400		0 -40	40	30	70
400 500		0 -45	45	34	80
500 630		0 -50	50	38	100
630 800		0 -70	70	55	120
800 1000		0 -100	100	75	120
1000 1250		0 -125	125	94	120
1250 1600		0 -160	160	120	120
1600 2000		0 -200			120
2000 2500		0 -250

Tolerances for DHK metric taper roller bearings (excluding tapered roller bearings)

All dimensions shown in (mm):

Tolerances in (um):

Inner Ring

Tolerance class P6X

Nominal bore diameter		Deviation	Variation	Variation	Ring width deviation	Radial runout	Ring width deviation
<=	<=	△dmp	Vdp	Vdmp	△Bs	Kia	△Ts	△T1s	△T2s
10 18		0 -12	12	9	0 -50	15	+100 0	+50～0	+50～0
18 30		0 -12	12	9	0 -50	18	+100 0	+50～0	+50～0
30 50		0 -12	12	9	0 -50	20	+100 0	+50～0	+50～0
50 80		0 -15	15	11	0 -50	25	+100 0	+50～0	+50～0
80 120		0 -20	20	15	0 -50	30	+100 0	+50～0	+50～0
120 180		0 -25	25	19	0 -50	35	+150 0	+50～0	+100～0
180 250		0 -30	30	23	0 -50	50	+150 0	+50～0	+100～0
250 315		0 -35	35	26	0 -50	60	+200 0	+100～0	+100～0
315 400		0 -40	40	30	0 -50	70	+200 0	+100～0	+100～0
400 500
500 630
630 800
800 1000

Outer Ring
Tolerance class P6X

Nominal outer diameter		Deviation	Variation	Variation	Ring width deviation	Radial runout
<=	<=	△Dmp	VDp	VDmp	△Cs	Kea
18 30		0 -12	12	9	0 -100	18
30 50		0 -14	14	11	0 -100	20
50 80		0 -16	16	12	0 -100	25
80 120		0 -18	18	14	0 -100	35
120 150		0 -20	20	15	0 -100	40
150 180		0 -25	25	19	0 -100	45
180 250		0 -30	30	23	0 -100	50
250 315		0 -35	35	26	0 -100	60
315 400		0 -40	40	30	0 -100	70
400 500		0 -45	45	34	0 -100	80
500 630		0 -50	50	38	0 -100	100
630 800
800 1000

The width tolerance △Cs is identical to△Bs of inner ring of the same bearing

Tolerances for DHK metric taper roller bearings (excluding tapered roller bearings)

All dimensions shown in (mm):

Tolerances in (um):

Inner Ring

Tolerance class P5

Nominal bore diameter		Deviation	Variation	Variation	Ring width deviation	Radial runout	Side face runout
<=	<=	△dmp	Vdp	Vdmp	△Bs	Kia	Ｓd	△Ts
10 18		0 -7	5	5	0 -200	5	7	+200 -200
18 30		0 -8	6	5	0 -200	5	8	+200 -200
30 50		0 -10	8	5	0 -240	6	8	+200 -200
50 80		0 -12	9	6	0 -300	7	8	+200 -200
80 120		0 -15	11	8	0 -400	8	9	+200 -200
120 180		0 -18	14	9	0 -500	11	10	+350 -250
180 250		0 -22	17	11	0 -600	13	11	+350 -250
250 315		0 -25	19	13	0 -700	16	13	+350 -250
315 400		0 -30	23	15	0 -800	19	15	+400 -400
400 500		0 -35	26	18	0 -900	22	17	+400 -400
500 630		0 -40	30	20	0 -1000	26	20	+500 -500
630 800		0 -50	50	25	0 -1500	30	26	+600 -600
800 1000		0 -65	60	30	0 -2000	35	32	+750 -750

Outer Ring
Tolerance class P5

Nominal outer diameter		Deviation	Variation	Variation	Radial runout	Outside inclination variation
<=	<=	△Dmp	VDp	VDmp	Kea
18 30		0 -8	6	5	6	8
30 50		0 -9	7	5	7	8
50 80		0 -11	8	6	8	8
80 120		0 -13	10	7	10	9
120 150		0 -15	11	8	11	10
150 180		0 -18	14	9	13	10
180 250		0 -20	15	10	15	11
250 315		0 -25	19	13	18	13
315 400		0 -28	22	14	20	13
400 500		0 -33	25	17	23	15
500 630		0 -38	29	19	25	18
630 800		0 -45	34	23	30	20
800 1000		0 -60	45	30	35	25
1000 1250		0 -80	75	38	40	30
1250 1600		0 -100	90	45	45	35

The width tolerance △Cs is identical to△Bs of inner ring of the same bearing

Tolerances for DHK metric taper roller bearings (excluding tapered roller bearings)
All dimensions shown in (mm):
Tolerances in (um):

Inner Ring
Tolerance class P4

Nominal bore diameter		Deviation	Variation	Variation	Ring width deviation	Radial runout	Side face runout	Side face runout	Ring width deviation
<=	<=	△dmp △ds	Vdp	Vdmp	△Bs	kia	Sd	Sia	△Ts
10 18		0 -5	4	4	0 -200	3	3	3	+200 -200
18 30		0 -6	5	4	0 -200	3	4	4	+200 -200
30 50		0 -7	6	5	0 -240	4	4	4	+200 -200
50 80		0 -8	7	5	0 -300	4	5	4	+200 -200
80 120		0 -10	8	5	0 -400	5	5	5	+200 -200
120 180		0 -13	10	7	0 -500	6	6	7	+350 -250
180 250		0 -15	11	8	0 -600	8	7	8	+350 -250

Outer Ring
Tolerance class P4

Nominal outer diameter		Deviation	Variation	Variation	Radial runout	Outside inclination variation	Side face runout
<=	<=	△Dmp △Ds	VDp	VDmp	Kea	SD	Sea
18 30		0 -6	5	4	4	4	5
30 50		0 -7	5	5	5	4	5
50 80		0 -9	7	5	5	4	5
80 130		0 -10	8	5	6	5	6
130 150		0 -11	8	6	7	5	7
150 180		0 -13	10	7	8	5	8
180 250		0 -15	11	8	10	7	10
250 315		0 -18	14	9	11	8	10
315 400		0 -20	15	10	13	10	13

The width tolerance △Cs and VCs are identical to△Bs and VBs of inner ring of the same bearing

The clearance of single row taper roller bearings is adjusted one bearing against another during mounting.

DHK taper roller bearing pairs arranged face-to- face (suffix DF) and back-to-back(suffix DB) are produced with internal clearance values, as listed in the table below. DHK can provide bearing pairs with special axial clearance upon request.

Axial Internal Clearance Of Paired DHK taper roller bearings,arranged face to face(DF) and back to back(DB)

Bore Dia. (mm)		Axial intcrnal clearance Series（μm）
>	<=	329 Min max	320 Min max X	330 Min max	331，3．2，332，332 Min max	303，323 Min max	313 Min max
-- 30		-- --	80 120	-- --	100 140	130 170	60 100
30 40		-- --	100 140	-- --	120 160	140 180	70 110
40 50		-- --	120 160	180 220	140 180	160 200	80 120
50 65		-- --	140 180	200 240	160 200	180 220	100 140
65 80		-- --	160 200	250 290	180 220	200 260	110 170
80 100		270 310	190 230	350 390	210 270	240 300	110 170
100 120		270 330	220 280	340 400	220 280	280 340	130 190
120 140		310 370	240 300	340 400	240 300	330 390	160 220
140 160		370 430	270 330	340 400	270 330	370 430	180 240
160 180		370 430	310 370	-- --	310 370	390 450	-- --
180 190		370 430	340 400	-- --	340 400	440 500	-- --
190 200		390 450	340 400	-- --	340 400	440 500	-- --
200 225		440 500	390 450	-- --	390 450	490 550	-- --
225 250		440 500	440 500	-- --	440 500	540 600	-- --
250 280		540 500	490 55	-- --	490 550	-- --	-- --
280 300		640 700	540 600	-- --	540 600	-- --	-- --
300 340		640 700	590 650	-- --	590 650	-- --	-- --

Model		Dimensions								Extreme speed		Rated load		Calculation factor			Abutment and fillet dimensions(mm)						Weight [kg]
DIN720	ISO355	d	D	B	C	T	r1,r2 min	r3,r4 min	a	Grease lubrication	Oil lubrication	Dynamic load	Static load	e	Y	Yo	Da max	db min	da min	Db min	Ca min	Cb min	Weight [kg]
3226	T4FD130	130	230	64	54	67.75	4	3	56	1500	2000	570	865	0.44	1.38	0.76	146	144	193	219	7	13.5	11.7
30202	--	15	35	11	10	11.75	0.6	0.6	10	12000	17000	12.2	11.4	0.46	1.3	0.72	21	21	29	32	2	2	0.06
30203	T2DB017	17	40	12	11	13.25	1	1	10	10000	15000	20	20	0.35	1.74	0.96	23	23	34	37	2	2	0.08
30204	T2DB020	20	47	14	12	15.25	1	1	11	8500	12000	28.5	29	0.35	1.74	0.96	27	26	40	43	2	3	0.13
30205	T3CC025	25	52	15	13	16.25	1	1	13	7500	10000	32.5	35.5	0.37	1.6	0.88	31	31	44	48	2	3	0.16
30206	T3DB030	30	62	16	14	17.25	1	1	14	6300	8500	44	49	0.37	1.6	0.88	37	36	53	57	2	3	0.22
30207	T3DB035	35	72	17	15	18.25	1.5	1.5	15	5300	7000	54	60	0.37	1.6	0.88	440	42	62	67	3	3	0.32
30208	T3DB040	40	80	18	16	19.75	1.5	1.5	17	4800	6300	62	68	0.37	1.6	0.88	49	47	69	74	3	3.5	0.43
30210	T3DB050	50	90	20	17	21.75	1.5	1.5	20	4300	5600	80	96.5	0.42	1.43	0.79	58	57	79	85	3	4.5	0.54
30211	T3DB055	55	100	21	18	22.75	2	1.5	21	3800	5000	91.5	108	0.4	1.48	0.81	64	64	88	94	4	4.5	0.7
30212	T3EB060	60	110	22	19	23.75	2	1.5	22	3400	4500	104	122	0.4	1.48	0.81	70	69	96	103	4	4.5	0.92
30213	T3EB065	65	120	23	20	24.75	2	1.5	23	3000	4000	120	143	0.4	1.48	0.81	77	74	106	113	4	4.5	1.1
30214	T3EB070	70	125	24	21	26.25	2	1.5	25	3000	4000	132	163	0.42	1.43	0.79	81	79	110	118	4	5	1.2
30215	T4DB075	75	130	25	22	27.25	2	1.5	27	2800	3800	137	173	0.44	1.38	0.76	86	84	115	124	4	5	1.4
30216	T3EB080	80	140	26	22	28.25	2.5	1.5	28	2400	3400	156	193	0.42	1.43	0.79	91	90	124	132	4	6	1.6
30217	T3EB085	85	150	28	24	30.5	2.5	2	30	2200	3200	180	228	0.42	1.43	0.79	97	95	132	141	5	6.5	2.1
30218	T3FB090	90	160	30	26	32.5	2.5	2	32	2000	3000	204	260	0.42	1.43	0.79	103	100	140	150	5	6.5	2.6
30219	T3FB095	95	170	32	27	34.5	3	2.5	34	1900	2800	224	285	0.42	1.43	0.79	110	107	149	159	5	7.5	3.2
30220	T3FB100	100	180	34	29	37	3	2.5	36	1900	2800	250	325	0.42	1.43	0.79	116	112	157	168	5	8	3.8
30221	T3FB105	105	190	36	30	39	3	2.5	38	1800	2600	280	365	0.42	1.43	0.79	122	117	165	177	6	9	4.2
30222	T3FB110	110	200	38	32	41	3	2.5	39	1700	2400	315	415	0.42	1.43	0.79	129	122	174	187	6	9	5.2
30224	T4FB120	120	215	40	34	43.5	3	2.5	43	1600	2200	340	455	0.44	1.38	0.76	140	132	187	201	6	9.5	6.8
30226	T4FB130	130	230	40	34	43.75	4	3	46	1500	2000	360	480	0.44	1.38	0.76	152	144	203	217	7	9.5	7.2
30228	T4FB140	140	250	42	36	45.75	4	3	47	1400	1900	425	570	0.44	1.38	0.76	163	154	219	234	9	9.5	8.5
30230	T4GB150	150	270	45	38	49	4	3	52	1300	1800	475	640	0.44	0.38	0.76	175	164	234	250	9	11	11.1
30232	T4GB160	160	290	48	40	52	4	3	51	1100	1600	405	585	0.37	1.61	0.89	189	174	252	269	9	12	13.2
30234	T4GB170	170	310	52	43	57	5	4	60	1000	1500	600	830	0.44	1.38	0.78	203	188	269	288	8	14	17
30236	T4GB180	180	320	52	43	57	5	4	62	1000	1500	570	800	0.45	1.33	0.73	211	198	278	297	9	14	17.9
30238	T4GB190	190	340	55	46	60	5	4	62	950	1400	530	780	0.39	1.56	0.86	224	207	298	318	9	14	21
30240	T4GB200	200	360	58	48	64	5	4	69	900	1300	1320	2160	0.44	2.31	1.52	237	217	315	336	9	16	25.1
30244	T4GB220	220	400	65	54	72	5	4	75	850	1200	950	1320	0.42	1.43	0.79	255	237	348	371	10	18	34.6
30248	--	240	440	72	60	79	5	4	--	800	1100	990	1400	0.44	1.4	0.74	290	267	401	422	--	--	45.2
30252	--	260	480	80	67	89	6	5	--	700	950	1190	1700	0.44	1.4	0.74	318	291	438	461	--	--	60.7
30256	--	280	500	80	67	89	6	5	--	700	950	1240	1900	0.44	1.4	0.74	336	313	456	478	--	--	66.3
30260	--	300	540	95	71	96	6	5	--	650	920	1440	2100	0.44	1.4	0.74	357	331	493	517	--	--	80.6
30264	--	320	580	92	75	104	6	5	--	600	800	1640	2420	0.44	1.4	0.74	382	354	529	554	--	--	99.3
30272	--	360	680	150	125	165	7.5	7.5	--	480	630	3690	6300	0.6	1	0.6	394	416	551	646	--	--	260

Ningbo DHK Precision Bearing Co., Ltd.

0+

Years Experience Working

0+

Customer Service

0+

Patented Technology

CERTIFICATE

DHK has passed IATF16949 quality system certification and ISO14001 environmental management system certification；and DHK is a national high-tech enterprise.

What are the key advantages of using Four Row Cylindrical Roller Bearings in heavy-duty applications?

2024-11-18 Industry News

Four Row Cylindrical Roller Bearings are specifically designed to handle both large radial and axial loads simultaneously, making them ideal for heavy-duty applications. The unique...

In what types of machinery or systems are paired single-row tapered roller bearings most commonly used?

2024-11-11 Industry News

In the automotive sector, paired single-row tapered roller bearings are commonly used in wheel hubs and axle assemblies. These bearings are essential for supporting both the radial...

How does the internal geometry of spherical roller bearings impact their load-carrying capacity?

2024-11-04 Industry News

One of the defining features of spherical roller bearings is the arrangement of two rows of rolling elements (typically cylindrical or barrel-shaped rollers) that run parallel to t...

What are the key benefits of using spherical roller bearings in heavy-duty applications?

2024-10-28 Industry News

Spherical roller bearings are designed to support both high radial and axial loads simultaneously, making them ideal for heavy-duty applications. Their unique internal geometry, wh...

How can the misalignment of angular contact ball bearings affect their operational efficiency?

2024-10-21 Industry News

Misalignment leads to uneven loading of the bearing's rolling elements, which disrupts their optimal contact with the raceways. This condition results in increased friction as the ...

How can improper installation affect the performance of paired single row tapered roller bearings?

2024-10-14 Industry News

Premature Wear: Improper installation of paired single row tapered roller bearings can lead to uneven contact patterns and load distribution, which are critical to their performanc...

Industry Knowledge Expansion

1. Understanding Series 30200 Single Row Tapered Roller Bearings

Series 30200 Single Row Tapered Roller Bearings are engineered to accommodate both radial and axial loads by virtue of their tapered design. This configuration enables efficient distribution of forces along the bearing axis, allowing for smooth and reliable operation even under demanding conditions. The tapered geometry of these bearings ensures that the contact between the rolling elements (tapered rollers) and the races (inner and outer rings) occurs at a precise angle, facilitating optimal load distribution and minimizing friction. Within the Series 30200, the inner ring (cone) and outer ring (cup) are meticulously designed to ensure proper alignment and fit, essential for maintaining structural integrity and load-bearing capacity. The tapered rollers, positioned between the inner and outer rings, transmit forces between the two races while accommodating any misalignment or deflection, thus mitigating stress concentrations and reducing the likelihood of premature wear or failure. Series 30200 bearings are equipped with a cage assembly that retains and guides the tapered rollers, ensuring uniform spacing and alignment. This feature not only enhances the overall stability of the bearing but also reduces frictional losses, contributing to improved efficiency and reduced operating temperatures. The design of Series 30200 Single Row Tapered Roller Bearings embodies a harmonious balance between structural integrity, load-carrying capacity, and operational efficiency. By virtue of their tapered configuration and meticulous engineering, these bearings stand as reliable assets in various industrial applications, providing exceptional performance and longevity.

2. Design Features and Construction

The construction of Series 30200 Single Row Tapered Roller Bearings is testament to precision engineering and meticulous craftsmanship. Each component is carefully crafted and assembled to exacting standards, ensuring optimal performance and longevity in diverse operating environments. The inner and outer rings of Series 30200 bearings are forged from high-quality steel, selected for its exceptional strength, durability, and resistance to deformation. Through advanced manufacturing processes such as precision grinding and heat treatment, these rings are meticulously finished to precise dimensions and surface finishes, facilitating smooth and efficient operation. The tapered rollers, another critical component of Series 30200 bearings, are engineered to withstand high radial and axial loads while minimizing frictional losses. These rollers are precisely machined and heat-treated to enhance hardness and durability, ensuring reliable performance under varying operating conditions. Complementing the inner and outer rings and tapered rollers is the cage assembly, typically constructed from steel or synthetic materials. The cage serves to retain and guide the rollers, preventing contact and friction between adjacent elements while maintaining proper spacing and alignment. This feature not only enhances the overall stability of the bearing but also promotes smoother rotation and reduced wear over time.

Tel
+86-574-86597612
Email
ken@dhk-intl.com
Phone
+86-13957821917
Fax
+86-574-86597652

Add

Building 31, Chuang E Huigu, No.777, West Zhongguan RoadZhenhai Economic Development Zone, Ningbo, Zhejiang, China

Web Menu

Product Search

Language

Exit Menu

Series 30200-Single Row Tapered Roller Bearings OEM/ODM

Categories

How Can We Help You?

Series 30200-Single Row Tapered Roller Bearings

Ningbo DHK Precision Bearing Co., Ltd.

0+

0+

0+

Click to view our factory

CERTIFICATE

Latest News

What are the key advantages of using Four Row Cylindrical Roller Bearings in heavy-duty applications?

In what types of machinery or systems are paired single-row tapered roller bearings most commonly used?

How does the internal geometry of spherical roller bearings impact their load-carrying capacity?

What are the key benefits of using spherical roller bearings in heavy-duty applications?

How can the misalignment of angular contact ball bearings affect their operational efficiency?

How can improper installation affect the performance of paired single row tapered roller bearings?

Industry Knowledge Expansion

CONTACT US

Tel

Email

Phone

Fax

Add

Web Menu

Product Search

Language

Share

Exit Menu

Series 30200-Single Row Tapered Roller Bearings OEM/ODM

Categories

How Can We Help You?

Series 30200-Single Row Tapered Roller Bearings

Ningbo DHK Precision Bearing Co., Ltd.

0+

0+

0+

Click to view our factory

CERTIFICATE

Latest News

What are the key advantages of using Four Row Cylindrical Roller Bearings in heavy-duty applications?

In what types of machinery or systems are paired single-row tapered roller bearings most commonly used?

How does the internal geometry of spherical roller bearings impact their load-carrying capacity?

What are the key benefits of using spherical roller bearings in heavy-duty applications?

How can the misalignment of angular contact ball bearings affect their operational efficiency?

How can improper installation affect the performance of paired single row tapered roller bearings?

Industry Knowledge Expansion

CONTACT US

Tel

Email

Phone

Fax

Add